Product Information
1、 Overview
This product adopts advanced microcontroller control circuit, with precise delay time. By displaying time and other parameters through a digital tube and adjusting the values with buttons, it greatly facilitates users' function selection and settings. Input signal optocoupler isolation (true isolation, completely isolated from power supply in electrical systems), can accept high/low levels, NPN/PNP signals, CMOS signals, etc.
2、 Characteristics:
Power input reverse protection
Signal input optocoupler isolation, supporting high and low level, NPN/PNP signals.
Dual anti-interference circuit design:
1) Anti input signal interference
2) Anti interference of relays on microcontrollers
Strong and weak current slot isolation
Authentic copper wire terminals can withstand 16A current.
Compliant with ROHS lead-free requirements and of export quality.
Relay reverse diode protection
The relay can be closed more than 100000 times
Power indicator light, relay working indicator light
Stable and reliable, strong anti-interference, designed specifically for industrial applications!
The maximum load capacity of the relay is AC250V10A current
Delay range 0~999 minutes
3、 Function code (V20190425)
Noun Explanation:
Signal giving "refers to the moment when a signal is received. Like the moment a button is pressed.
2 "Signal": Refers to the constant presence of a signal, similar to pressing a button all the time.
3 "Suction": refers to the suction of the common end and the normally open end (while the common end and the normally closed end will be disconnected)
4 "Disconnected": refers to the disconnection of the common end and the normally open end (while the common end and the normally closed end will be attracted).
5. X, Y, Z are parameters/values, and the setting method can be found in "IV. Instructions for Use".
| 功能 代碼 Function code | 功能詳解 Function Explanation |
| 延時斷開系列功能: Delay disconnect series function: | |
| F10 | 通電后繼電器吸合，延時X時間，繼電器斷開. After being powered on, the relay is engaged, delayed for X time, and disconnected. |
| F11 | 1.通電無動作，等待信號。 2.給信號，繼電器吸合，延時X時間，繼電器斷開。(延時期間給信號無效)。 3.等待信號(重復步驟2)。 1. No action when powered on, waiting for signal. 2. Give the signal, the relay is engaged, delayed for X time, and the relay is disconnected. The signal is invalid during the delay period. 3. Wait for the signal (repeat step 2). |
| F12 | 1.通電無動作，等待信號。 2.給信號，繼電器吸合，延時X時間，繼電器斷開。(延時期間給信號重新延時)。 3.等待信號(重復步驟2)。 1. No action when powered on, waiting for signal. 2. Give the signal, the relay is engaged, delayed for X time, and the relay is disconnected. (Delay the signal again during the delay period). 3. Wait for the signal (repeat step 2). |
| F13 | 1.通電無動作，等待信號。 2.給信號，繼電器吸合，信號消失才開始計時，延時X時間，繼電器斷開。(延時期間給信號無效） 3.等待信號(重復步驟2) 1. No action when powered on, waiting for signal. 2. Give the signal, the relay will close, and the timing will only start when the signal disappears. After a delay of X time, the relay will disconnect. (Signal invalid during delay period) 3. Wait for signal (repeat step 2) |
| F14 | 1.通電無動作，等待信號。 2.給信號，繼電器吸合，信號消失才開始計時，延時X時間，繼電器斷開。(延時期間給信號重新延時)。 3.等待信號(重復步驟2) 1. No action when powered on, waiting for signal. 2. Give the signal, the relay will close, and the timing will only start when the signal disappears. After a delay of X time, the relay will disconnect. (Delay the signal again during the delay period). 3. Wait for signal (repeat step 2) |
| 延時接通 系列功能: Delay connection series functions: | |
| F20 | 通電后，延時X時間，繼電器吸合。 After power on, delay for X time and the relay will close. |
| F21 | 1.通電無動作，等待信號。 2.給信號，延時X時間，繼電器吸合。(延時期間給信號無效) 3.等待信號(重復步驟2)。(注意:此后來信號的時候繼電器會先斷開) 1. No action when powered on, waiting for signal. 2. Give the signal, delay for X time, and activate the relay. (Signal invalid during delay period) 3. Wait for the signal (repeat step 2). (Note: The relay will disconnect first when the signal is received later.) |
| F22 | 1.通電無動作，等待信號。 2.給信號，延時X時間，繼電器吸合。(延時期間給信號重新延時) 3.等待信號(重復步驟2)。(注意:此后來信號的時候繼電器會先斷開) 1. No action when powered on, waiting for signal. 2. Give the signal, delay for X time, and activate the relay. (Delay the signal again during the delay period) 3. Wait for the signal (repeat step 2). (Note: The relay will disconnect first when the signal is received later.) |
| F23 | 1.通電無動作，等待信號。 2.給信號，延時X時間(延時期間給信號無效)，繼電器吸合。再給信號，繼電器立即斷開。 3.等待信號(重復步驟2)。 1. No action when powered on, waiting for signal. 2. Give the signal, delay for X time (the signal is invalid during the delay period), and the relay will close. Give the signal again, and the relay will immediately disconnect. 3. Wait for the signal (repeat step 2). |
| F24 | 1.通電無動作，等待信號。 2.有信號，開始延時，X時間，繼電器吸合。 3.無信號，繼電器立刻斷開 1. No action when powered on, waiting for signal. 2. There is a signal, start delay, X time, and the relay is closed. 3. If there is no signal, the relay will immediately disconnect |
| F25 | 1.通電無動作，等待信號。 2.給信號，延時X時間(延時期間給信號回到步驟1)，繼電器吸合 3.再給信號，繼電器立即斷開。等待信號(重復2) 1. No action when powered on, waiting for signal. 2. Give the signal, delay for X time (give the signal back to step 1 during the delay period), and the relay will close 3. Give the signal again, and the relay will immediately disconnect. Waiting for signal (repeat 2) |
| 延時循環 系列功能: Delay cycle series function: | |
| F30 | 通電后，繼電器吸合X時間斷開Y時間，循環吸合斷開Z次。Z=0時無限循環。 After power on, the relay will engage for X time and disconnect for Y time, cycling on and off Z times. Infinite loop when Z=0. |
| F31 | 1.通電無動作，等待信號。 2.有信號:繼電器吸合X時間斷開Y時間吸合X...一直循環。 3.信號消失:終止循環且繼電器斷開。 1. No action when powered on, waiting for signal. 2. There is a signal: the relay is closed at X time, disconnected at Y time, and closed at X Keep cycling. 3. Signal disappearance: Terminate the cycle and disconnect the relay. |
| F32 | 1.通電無動作，等待信號。 2.給信號，繼電器吸合X時間斷開Y時間吸合X..一直循環。 3.再給信號，終止循環且繼電器斷開。 1. No action when powered on, waiting for signal. 2. Give the signal, the relay will close X, disconnect Y, and close X Keep cycling. 3. Give another signal to terminate the cycle and disconnect the relay. |
| F33 | 1.通電無動作，等待信號 2.給信號，繼電器吸合x時間斷開Y時間。(延時期間給信號無效) 3.重復步驟2(等待信號)。重復Z次后(共待信號Z次)，一直斷開。Z=0時無限循環。 1. No action when powered on, waiting for signal 2. Give the signal, the relay will be closed for x time and disconnected for Y time. (Signal invalid during delay period) 3. Repeat step 2 (wait for signal). After repeating Z times (waiting for signal Z times in total), keep disconnecting. Infinite loop when Z=0. |
| F34 | 1.通電無動作，等待信號。 2.給信號，延時X時間，繼電器吸合，延時Y時間，繼電器斷開。(延時期間給信號無效) 3.重復步驟2(等待信號)。重復Z次后(共等待信號Z次)，一直斷開。Z=0時無限循環. 1. No action when powered on, waiting for signal. 2. Give signal, delay for X time, relay on, delay for Y time, relay off. (Signal invalid during delay period) 3. Repeat step 2 (wait for signal). After repeating Z times (waiting for signal Z times in total), keep disconnecting. Infinite loop when Z=0 |
| 更多功能陸續更新，請以購買時的規格書為準。支持功能定制! More features will be updated gradually, please refer to the specification sheet at the time of purchase. Support customization of functions! | |
| 備注： Remarks: | |
| 1.每個功能的參數都是獨立的，掉電保存。 2.出廠默認所有X=10，Y=5，Z=0。參數最大值為999 3.Z為0時表示無限循環 1. The parameters of each function are independent and saved in case of power failure. 2. By default, all X values are set to 10 when leaving the factory, Y=5，Z=0。 The maximum value of the parameter is 999 3. When Z is 0, it means infinite loop | |
| 友情提醒:如果發現功能異常，檢查當前X,Y參數值，有可能是0，請按照自己需求設置。 Friendly reminder: If any functional abnormalities are found, check the current X and Y parameter values, which may be 0. Please set them according to your own needs. | |
4、 Instructions for use:
1. Interface definition:
| 接口 Interface | 說明 Description | 備注 Remarks | |
| 控制端 Control end | DC+ | 供電電源正極 Positive pole of power supply | 1.電壓范圍見《產品選型表》 2.電源電流需要能提供一定的電流，詳見《產品選型表》 1. The voltage range is shown in the "Product Selection Table" 2. The power supply current needs to be able to provide a certain amount of current, as detailed in the "Product Selection Table"“ |
| DC- | 供電電源負極 Negative pole of power supply | ||
| S+ | 觸發信號正極 Trigger signal positive pole | 當信號電壓大于 2V即可觸發。 When the signal voltage is greater than 2V, it can be triggered. | |
| S- | 觸發信號負極 Trigger signal negative pole | ||
| 負載端 Load end | 常開端 Constant Beginning | 繼電器常開端 Relay often starts | 類似一個開關，沒有電壓電流輸出 Similar to a switch, without voltage or current output |
| 公共端 Public end | 繼電器公共端 Relay common terminal | ||
| 常閉端 Always closed end | 繼電器常閉端 Relay normally closed end |
2. Button Description:
FUN key: Stop key, displays function code.
SET key: Set key, Shift key.
NUM key: numerical adjustment key (adjust each digit from 0 to 9)
3. Explanation of decimal point for delay time
XX. X The decimal point of X is in ten places, and the timing range is 0.1 seconds to 99.9 seconds
XXX. The decimal point is in units, and the timing range is 1 second to 999 seconds
X. X.X. decimal point fully lit, timing range: 1 minute to 999 minutes
Remarks:
(1) When setting parameters X and Y, the first setting is the decimal point (flashing), and press the NUM key to switch
(2) Parameter Z is the number of cycles, without a decimal point.
(3) The decimal point position of each parameter in each function is independent and adjustable, does not affect each other, and is saved in case of power failure
4. Status description:
5. Set parameters:
Each function has a different number of parameters. According to the 'Function Code', there are up to three parameters X Y、Z。 In any state, press the FUN key to emergency stop and return to the stop state, displaying the function code for the day as shown in Figure 1. Press the NUM key to select the desired function, and then press and hold the SET key for 2 seconds to enter the setting mode.
(1) After entering the setting mode, the screen displays the value of the first parameter X, and the decimal point flashes. Press the NUM key to select the decimal point position. The meaning of the position can be found in "3. Explanation of the decimal point of delay time".
(2) Press the SET key again, and the highest digit of the value will start flashing. Press the NUM key to adjust the value from 0 to 9 in a loop. Press the SET key again, and the flashing will shift to ten digits. Similarly, press the NUM key to adjust the value. Press the SET key again, flash to shift to one bit, and press the NUM key to adjust the value.
(3) When pressing the SET key again, if there is a second parameter Y, it will start displaying the second parameter Y and the decimal point will flash. Similarly, as in (2).
(4) If there is a third parameter Z, the same applies to (2).
(5) After setting, pressing the SET key will return to the working state (if the function is triggered by a signal, it will display Figure 2, which means waiting for the signal to trigger; if it is triggered by power on, it will display Figure 3, which means waiting for restart).
In the setting state, no matter where you are, long press the SET key for 2 seconds to quickly save the current settings and enter the working state.
Product Details
Product Parameter
| 型號 Model | 繼電器 最大負載電流/電壓 Relay Maximum load current/voltage | 供電電壓 Supply voltage (VDC) | 最小供電電流 Minimum supply current (mA) | 信號電壓范圍 Signal voltage range (VDC) | 備注 Notes |
| JK-DE-3V | 阻性負載10A Resistive load 10A 感性負載5A Inductive load 5A / 交流250VAC或直流 30VD) AC 250VAC or DC 30VD) | 3V~4V | 130mA | 2V~7V | |
| JK-DE-5V | 4.5V~5.5V | 85mA | 2V~7V | ||
| JK-DE-12V | 11V~14V | 40mA | 3V~24V | ||
| JK-DE-24V | 23V~26V | 25mA | 3V~24V |
5.Product Performance
| 項目 Project | 性能 Performance | 注釋 Notes | |
| 最大切換電壓 Maximum switching voltage | 250VA | ||
| 最大切換電流 Maximum switching current | 10A | ||
| 吸合反應時間 Adsorption reaction time | 10msec(MAX) | 最高10毫秒 Maximum 10 milliseconds | |
| 釋放反應時間 Release reaction time | 5msec(MAX) | 最高5毫秒 Up to 5 milliseconds | |
| 絕緣耐壓 Dielectric Strength | 線圈和觸點 Coil and contact points | 1500VAC 50/60HZ(1 minute) | |
| 觸點間 Between contact points | 1000VAC 50/60HZ(1 minute) | ||
| 開關頻率 Switching frequency | 無負載 No load | 300 operation/min | 300次/分鐘 |
| 有負載 Under load | 30 operation/min | 30次/分鐘 | |
| 待機功耗 Standby power consumption | 18mA | 典型值 Typical values | |
| 工作溫度 Working temperature | -40°C to +85°C | ||
| 工作濕度 Working humidity | 45 to 85% RH | ||
| 存儲溫度 Storage temperature | -65~150℃ | ||
| 壽命 Life | 無負載 No load | 10 operations. Min. | 最少1000 萬次 At least 10 million times |
| 有負載 Under load | 10 operations. Min. | 最少10 萬次 At least 100000 times | |
Product Size
Application Circuit
Product Display
Payment&Transportation
Official Certificate&Certificate
Multiple product supply
Company office environment
Warehouse Real Shot
Standard packaging
We also provide ：
| Part No | Manufacturer | Date Code | Quantity | Description |
| LM22676ADJ | NS | 19+ | 250 | SOP8 |
| TPS562201DDCR | TI | 22+ | 795500 | SOT23-6 |
| NJG1806K75 | JRC | 22+ | 500000 | DFN6 |
| TLV74318PDQNR | TI | 22+ | 402000 | X2SON-4 |
| NJG1801K75 | JRC | 22+ | 300000 | SMD |
| NJG1804K64 | JRC | 22+ | 300000 | DFN8 |
| LM27761DSGR | TI | 22+ | 151000 | WSON8 |
| TLV62565DBVR | TI | 22+ | 138000 | SOT23-5 |
| TPS613222ADBVR | TI | 22+ | 108000 | SOT23-5 |
| LNK625DG-TL | POWER | 22+ | 100000 | SOP-8 |
| OPA4322AIPWR | TI | 22+ | 100000 | TSSOP14 |
| TLV75528PDRVR | TI | 22+ | 99000 | WSON-6 |
| TPS7A2025PDQNR | TI | 22+ | 78500 | X2SON-4 |
| TLV62568DBVR | TI | 22+ | 72000 | SOT23-5 |
| STM32L051K8U6TR | ST | 22+ | 60000 | QFN32 |
| SKY66421-11 | SKYWORKS | 22+ | 56500 | QFN16 |
| TPS7A1111PDRVR | TI | 22+ | 54000 | WSON6 |
| TLV62569PDDCR | TI | 22+ | 52000 | SOT23-6 |
| TLV62569DBVR | TI | 22+ | 48000 | SOT23-5 |
| TPS23753APWR | TI | 22+ | 40000 | TSSOP14 |
| NB691GG-Z | MPS | 22+ | 30000 | QFN |
| SN74AHC1G02DBVR | TI | 22+ | 27939 | SOT-23 |
| TPS63000DRCR | TI | 22+ | 23238 | VSON10 |
| TLV75533PDRVR | TI | 22+ | 21500 | WSON6 |
| NB687BGQ-Z | MPS | 22+ | 20000 | QFN |
| A3916GESTR-T-1 | ALLEGRO | 22+ | 17150 | QFN-20 |
| TPS62135RGXR | TI | 22+ | 15000 | VQFN11 |
| TLE2022AMDR | TI | 0803+ | 12500 | SOP8 |
| TPS23756PWPR | TI | 22+ | 12000 | HTSSOP-20 |
